9 results for "Shanquan Deng"
Showing 1–9 · 0.43 seconds · RSS
-
Journal Article
区域一维速度模型对地震定位的定量影响
利用2017年8月1日至2017年12月31日四川地震台网和甘肃地震台网记录到的发生在青藏高原东缘的731个地震事件的9 284条Pg震相到时数据,首先反演了该地区的“最小一维速度模型”,并将该模型和选取的速度模型建立对比模型,以九寨沟地震序列为研究目标,定量讨论了两种速度模型分别在绝对定位和相对定位方法中对定位结果的影响。所得定位结果表明:反演获得的“最小一维速度模型”在重定位中可以有效地减小地震走时均方根残差;绝对定位比相对定位更加依赖于一维速度模型,一维速度模型会直接影响绝对定位结果中的震源分布形态,但在相对定位结果中仅起到调整地震事件相对位置的作用;在地震绝对定位中,震级越大的地震对于…
-
Journal Article Full text
Coupled Effects of Mg/Si Ratio and Recrystallization on Strength and Electrical Conductivity in Al-xMg-0.5Si Alloys
The strategic balance between strength and electrical conductivity in Al-Mg-Si alloys is a critical challenge that must be overcome to enable their widespread adoption as viable alternatives to copper conductors in power transmission systems. To address this, the present study comprehensively…
-
Journal Article Full text
Microstructure Evolution and Property Enhancement of Hot-Rolled 5083 Aluminum Alloy During Homogenization Annealing
The 5083 aluminum alloy is widely used in marine engineering due to its excellent corrosion resistance and weldability. To address microstructural defects that may arise during hot rolling, homogenization annealing is employed as a critical post-processing step to enhance mechanical and processing…
-
Journal Article Full text
Modification Strategies and Microstructure–Property Relationships of 6xxx and 8xxx Aluminum Alloy Conductors for Wires and Cables
With the rapid transition of power transmission systems toward higher capacity, longer distance, and improved efficiency, aluminum alloys from the 6xxx (Al–Mg–Si) and 8xxx (Al–Fe) series have become key structural materials for overhead conductors and power cables due to their low density, cost…
-
Journal Article
Synergistic control of composition and processing in Al-Mg-Si alloy conductors: development and performance mechanism investigation
This study aims to address the critical challenge of synergistically optimizing strength and electrical conductivity in Al-Mg-Si alloy conductors, in response to the growing demand for high-performance conductive materials in smart grids and lightweight transmission lines. By systematically…
-
Journal Article
Study on the mechanical and electrical properties of as-cast and wrought Al–xCu–0.25Mg alloys
In this study, the mechanical and electrical properties of as-cast and thermomechanically treated Al– x Cu–0.25Mg alloys ( x = 0–1.25 wt%) were systematically investigated, with the Mg content fixed at 0.25 wt% to isolate the effect of Cu addition. In the as-cast state, increasing the Cu content…
-
Journal Article Full text
Study on the Coupling Mechanism of Si Content on the Microstructure Evolution and Strength–Conductivity Properties in Low-Magnesium Al-0.2Mg-xSi Alloys
High-silicon, low-magnesium aluminum alloys are important for lightweight electrical applications, yet they face a typical strength–conductivity trade-off. This study investigates Al-0.2Mg-xSi alloys with Si ranging from 0.4 to 1.0 wt%. The wires underwent homogenization, solution treatment, cold…
-
Journal Article
Synergetic enhancement of strength and ductility by heterogeneous architecture in interpenetrating copper and graphene‑copper composite
Metal matrix composites exhibit an obvious decrease in ductility and toughness as strength increases. Inspired by the heterostructure characteristics of biological materials, this study designs a coarse-grained/ultrafine-grained heterostructure. A copper foam/graphene‑copper (Gr-Cu) heterostructure…
-
Journal Article Full text
Microstructure Modification and Property Enhancement of Al-0.5Fe Alloy via Equimolar La/Ce Co-Doping: Mechanisms and Composition-Dependent Effects
The effects of equimolar La/Ce co-doping (0–0.4 wt.% of each element) on the microstructure, mechanical properties, and electrical conductivity of the Al-0.5Fe (8176) conductor alloy were investigated in the as-cast, cold-drawn, and annealed (300 °C, 2 h) states. La/Ce additions refine the as-cast…