12.729 hasil
Menampilkan 281–300 · 1,97 detik · RSS
-
Artikel Jurnal
A study on the improvement of the Pure Pursuit Method (Analysis of a tracking system using the Dual Preview Points Method)
The Pure Pursuit method has been widely used as a standard approach in many autonomous vehicles due to its ease of implementation and low computational cost. However, there is a trade-off between responsiveness and preview distance: while a longer preview distance is necessary to accommodate sudden…
-
Artikel Jurnal
Proposal of a method for estimating gripped object mass in stoop lifting using a 9-axis sensor
In recent years, low back pain(LBP) among manufacturers has become a problem. One causes of LBP is the lifting of loads. It has been confirmed that the stoop lifting, where the object is lifted by bending forward with extended knees, puts more strain on the lower back than squat lifting, where the…
-
Artikel Jurnal
Development of a method for deriving vehicle shapes and flow fields for low aerodynamic drag using machine learning
Due to rapid changes in the market and various customer values, it is necessary to shorten the development period of automobiles. Vehicle performance has been improved mainly through experimental analysis and CAE (computer aided engineering). In the increasingly rapid development of vehicles…
-
Artikel Jurnal
Measurement of boiling behaviour in a horizontal heat circular tube with a transparent heating model for low GWP refrigerant
As part of a study to improve the efficiency of two-phase flow systems using HFO refrigerants, a correlating equation for predicting heat transfer coefficient has been proposed. In particular, the separation angle, which is the boundary between the liquid and gas phases, is an important parameter…
-
Artikel Jurnal
Analysis of reduction effect of the cervical spine load in the presence of the headrest which can be attached to the assist device for upward work
In this paper, effectiveness of the headrest which can be attached to the assist device for upward work was investigated based on the static and dynamic analyses. In the static analysis, the cervical spine load model was proposed and static strain on the cervical spine was evaluated. As a result…
-
Artikel Jurnal
Convenient stress concentration formula useful for any shape of fillet (Torsion of stepped round bar with fillet)
To ensure the strength and safety of shafts, which are basic components of machines, it is important to accurately evaluate the stress concentration factor (SCF) of stepped round bar fillets. Noda et al. analyzed the SCF of stepped round bar with fillet under tension and bending by using the body…
-
Artikel Jurnal
Topology optimization for thermal-fluid systems considering maximum temperature constraints
This paper presents a topology optimization method for minimizing power dissipation while constraining the maximum temperature in thermal-fluid systems. The advantage of the proposed optimization is its ability to accurately approximate the maximum temperature constraint as a continuous function…
-
Artikel Jurnal
Refining the ambulance travel model for more accurate transport time estimation
This paper refines the ambulance travel model, which is used to determine the optimal route from an emergency site to a hospital, to enhance the accuracy of travel time estimation. The model provides driving rules regarding the acceleration and velocity of the ambulance under the assumption that it…
-
Artikel Jurnal
Basic study on a rotary focus-tunable freeform microlens fabricated using two-photon micro stereolithography
Recent advancements in two-photon micro stereolithography have enabled the fabrication of complex micro optics with freeform surfaces. However, the design of freeform microlenses for optical MEMS (Micro Electro Mechanical System) applications remains underexplored. This paper presents a rotary…
-
Artikel Jurnal
Comparison of the characteristics of resin multi hole regenerators and stainless steel mesh regenerators in low temperature difference Stirling engine
The characteristics of resin multi hole regenerators (R-MHR) and stainless steel mesh regenerators (SMR) were compared in a low temperature difference Stirling engine. Comparing equalized regenerators in the engine with a swept volume of 5 cc and the temperature difference of 80 K, the measured…
-
Artikel Jurnal
Development of regularization method for physics problems using PINNs and data augmentation using equation discovery technique
This study proposes a regularization method for high-accuracy prediction by machine learning under small data conditions by combining Physics-Informed Neural Networks (PINNs) and data augmentation based on equation discovery using Sparse Identification of Nonlinear Dynamical Systems (SINDy). PINNs…
-
Artikel Jurnal
Effects of surface modification on the adhesive and structural strength of CFRP-to-metal laminates using A5052 and SUS304
This study systematically evaluates the effects of surface treatment methods and adhesive types on the bonding strength between carbon fiber reinforced polymer (CFRP) and two commonly used metals: stainless steel (SUS304) and aluminum alloy (A5052). Three surface conditions—untreated, sanded, and…
-
Artikel Jurnal
Parameter estimation and wobbling behavior reproduction in lean-operable bicycle simulator
Bicycles are regarded as one of the major risk factors for vehicles. In particular, the behavior prediction of bicycle would be a critical issue for design of autonomous driving system. The utilization of simulation is increasingly expected to efficiently and safely evaluate bicycle-related safety…
-
Artikel Jurnal
Control of gasoline engine knocking based on a zero-dimensional heat balance model
A knocking control system based on a zero-dimensional heat balance model was implemented on a 1.6L conventional turbocharged gasoline engine to improve the thermal efficiency of internal combustion engines. The zero-dimensional model has been used to predict the exhaust port temperature, with its…
-
Artikel Jurnal
Injury prediction of standing passengers gripping a strap during emergency braking using a human finite element model considering muscle activity (Influence of nearby standing passengers)
In public transportation systems such as trains and buses, where passengers frequently travel in a standing position, the risk of falling due to sudden deceleration—such as during Autonomous Emergency Braking (AEB)—poses a significant safety concern. However, conducting physical experiments under…
-
Artikel Jurnal
Effect of shear and elongational flows on strength of polymeric liquid crystal moldings
The effect of elongational flows during molding processes on the tensile strength of polymeric liquid crystal (PLC) plastics has been experimentally investigated. It is known that the molecular orientation profile in PLC plastics exhibits the skin-core structure, characterized by a high molecular…
-
Artikel Jurnal
Development of wearable device for measuring joint motion based on parallel wire-driven mechanism
In human rehabilitation, the measurement of joint range of motion (ROM) is essential in evaluating the degree of disability and recovery of patients. In clinical practice, ROM is typically measured with an angle meter, but its accuracy depends on the skill level of the measurer, and the task is…
-
Artikel Jurnal
Necessity and usefulness of analyzing 3D corner singularity index and 3D corner ISSF to evaluate adhesive strength
In this paper, necessity and usefulness of analyzing intensity of singular stress filed (ISSF) at 3D interface corner are discussed to evaluate adhesive strength of scarf joint. Previous studies showed that the adhesive strength of scarf joints can be expressed as a constant critical 2D ISSF at the…
-
Artikel Jurnal
Performance prediction of air drag brake units for Shinkansen and verification by running test
The performance of Air Drag Brake (ADB) units for Shinkansen trains was predicted using wind tunnel experiments and numerical analysis, and running tests were carried out using a test car equipped with a number of ADB units. First, A large scale wind tunnel experiment was carried out with 20 ADB…
-
Artikel Jurnal
Proposal of determination method for the material parameters of the GTN model based on sensitivity analysis by the Monte Carlo method
Fracture analysis using damage mechanics models such as the GTN (Gurson-Tvergaard-Needleman) model is applied for the purpose of limit load or limit strain evaluation of structures. It has been pointed out that failure analysis using a damage mechanics model is affected by element size. In general…
Menampilkan maksimal 50 halaman. Persempit pencarian dengan filter untuk hasil yang lebih spesifik.