Biblio Discovery — Demo Discovery Service

187 results for "Optimization"

Showing 1–20 · 0.94 seconds · RSS

  1. Journal Article Full text

    Shape Optimization of a Hydraulic Crane Boom

    Jae Hyoung Lee; Tae Hwa Song; Jai Hak Lee

    한국정밀공학회지, Vol. 35 No. 4 · 2018 · Korean · DOAJ Scopus

    …are required to maintain the tunnels cleanliness. As a study on shape optimization using the design of experiment, this paper assessed the design parameters affecting the maximum stress of an articulated hydraulic crane boom. As a result, the maximum stress of an optimized boom was 223.94 MPa at…

  2. Journal Article Full text

    Development of Design Optimization Module for Hydrostatic Bearings

    Gyungho Khim; Jeong Seok Oh

    한국정밀공학회지, Vol. 40 No. 12 · 2023 · Korean · DOAJ Scopus

    This paper presents the development of a design optimization module for achieving the best performance of hydrostatic bearings. The design optimization module consists of two components: a bearing performance analysis module and an optimization module that utilizes optimization algorithms. Widely…

  3. Journal Article

    Optimization of MRI Protocol for the Musculoskeletal System

    Hong Seon Lee; Young Han Lee; Inha Jung et al.

    대한영상의학회지, Vol. 81 No. 1 · 2020 · Korean · DOAJ

    Magnetic resonance imaging (MRI) is an essential modality for the diagnosis of musculoskeletal system defects because of its higher soft-tissue contrast and spatial resolution. With the recent development of MRI-related technology, faster imaging and various image plane reconstructions are…

From your institution’s collections

Perpustakaan Kampus · 12 print titlesShow all
  1. Journal Article Full text

    Lightweight Design of the Stub Axle Using Topology Optimization

    Jinsu Kim; Hong Seong Roh; Yeonjoo Min et al.

    한국정밀공학회지, Vol. 35 No. 7 · 2018 · Korean · DOAJ Scopus

    …in the event of review of a fully loaded in a box trailer. A topology optimization is conducted to determine a lightweight design for minimizing compliance under these boundary conditions.

  2. Journal Article Full text

    Improvement of Electrolyte Layer Coating Quality Using Statistical Optimization

    Seongyong Kim; Changwoo Lee

    한국정밀공학회지, Vol. 36 No. 2 · 2019 · Korean · DOAJ Scopus

    …layer have been conducted. However, few studies have been done on the optimization of slot-die coater geometry owing to the high cost associated with its fabrication. In this study, we optimize the geometry of the slot-die coater using computational fluid dynamics. We used a statistical…

  3. Journal Article Full text

    Shape Optimization of a Link of the Knuckle Crane

    Tae Hwa Song; Jai Hak Lee

    한국정밀공학회지, Vol. 36 No. 1 · 2019 · Korean · DOAJ Scopus

    …small knuckle cranes is evaluated through Finite Element Analysis. Shape optimization was performed using the Design of Experiment for parts speculated to have failed from fatigue. As a result, maximum equivalent stress of a plate in link speculated to have failed from fatigue was reduced by…

  4. Journal Article

    Optimization of the in vitro fertilization system in pigs

    Song-Hee Lee; Xiang-Shun Cui

    Journal of Animal Reproduction and Biotechnology, Vol. 38 No. 2 · 2023 · Korean · DOAJ

    Background: Despite considerable technological advancements, polyspermy remains a significant challenge in in-vitro fertilization (IVF) procedures in pigs, disrupting normal embryonic development. Here, we aimed to determine whether optimal fertilization conditions reduce the polyspermy incidence…

  5. Journal Article Full text

    Optimization of Manufacturing Layout Using Deep Reinforcement Learning and Simulation

    Ye Ji Choi; Minsung Kim; Byeong Soo Kim

    한국정밀공학회지, Vol. 42 No. 3 · 2025 · Korean · DOAJ Scopus

    …FLP than traditional techniques, addressing both physical and operational optimization.

  6. Journal Article Full text

    Topology Optimization of Main Rollers for Multi-Wire Saw Systems

    Jun Young Lee; Seung Eun Lee; Hong Jae Yim et al.

    한국정밀공학회지, Vol. 34 No. 10 · 2017 · Korean · DOAJ Scopus

    In this paper, topology optimization of a main roller for Multi-wire saws is conducted for the purpose of reducing mass of the main roller. Modal analysis is carried out to evaluate whether the resonance could have occurred, or not. The pressure from the cutting wires are modelled mathematically…

  7. Journal Article Full text

    Cutting Condition Optimization of Micro Hole for Single Crystal Silicon

    Eun Young Lee; Wang Ki Choi; Joong Hak Yoo

    한국정밀공학회지, Vol. 34 No. 8 · 2017 · Korean · DOAJ Scopus

    Micro hole drilling in precision production industries requires smaller holes, higher aspect ratios, and higher working speeds. However, the undesirable characteristics of micro drilling are small signal to noise ratios, wandering drill motion, high aspect ratio, and increasing cutting quality as…

  8. Journal Article Full text

    Process Monitoring and Part Program Optimization Using Virtual Machine Tools

    Chang-Ju Kim; Segon Heo; Chan-Young Lee et al.

    한국정밀공학회지, Vol. 39 No. 12 · 2022 · Korean · DOAJ Scopus

    …stability detection, machining error estimation, and part program optimization, were evaluated through various machining tests with a vertical 3-axis milling machine.

  9. Journal Article

    Optimization based machine learning algorithms for software reliability growth models

    Myeongguen Shin; Juwon Jung; Jihyun Lee et al.

    선진국방연구, Vol. 8 No. 1 · 2025 · Korean · DOAJ

    …are widely used. However, many previous studies have relied on single optimization methods or deep learning approaches, which are prone to local optima and extrapolation issues, reducing prediction accuracy. To fill this gap, current study employs a broader range of optimization algorithms based on…

  10. Journal Article Full text

    Optimization Design of Student KSAE BAJA Knuckle Using SLM 3D Printer

    Young Woo Im; Geon Taek Kim; Hyeon Sang Shin et al.

    한국정밀공학회지, Vol. 40 No. 9 · 2023 · Korean · DOAJ Scopus

    …this study conducts static and modal analyses, along with topology optimization. Additionally, experimental test drives are performed with the parts installed in KSAE BAJA vehicles, and modal frequency experiments are conducted. The objective of these analyses and experiments is to assess the…

  11. Journal Article Full text

    Response Surface Optimization of Turbidity Removal Using Plant-Based Mixed Coagulant

    Hyeon-Seung Kim; Ji-Eun Ahn; Johng-Hwa Ahn

    대한환경공학회지, Vol. 48 No. 1 · 2026 · Korean · DOAJ

    Optimal conditions for turbidity removal from synthetic wastewater were investigated using a mixed plant-based coagulant. Synthetic wastewater was prepared by suspending kaolin powder in distilled water and adjusting the final turbidity to 500 NTU. The mixed coagulant was prepared by extracting…

  12. Journal Article Full text

    Optimization of Culture and Sporulation for Two Plant Beneficial Streptomyces Strains

    Da-Ran Kim; Youn-Sig Kwak

    Research in Plant Disease, Vol. 29 No. 2 · 2023 · Korean · DOAJ Scopus

    The limited effectiveness of current plant disease management treatments necessitates the development of new methods for controlling diseases using beneficial microbes. Demanding sustainable agriculture is increasingly highlighted as a biocontrol approach, particularly Streptomyces species known to…

  13. Journal Article

    Optimization of Automated Solid Phase Extraction-based Synthesis of [18F]Fluorocholine

    Jun Young PARK; Jeongmin SON; Won Jun KANG

    Korean Journal of Clinical Laboratory Science, Vol. 55 No. 4 · 2023 · Korean · DOAJ

    [18F]Fluorocholine is a radiopharmaceutical used non-invasively in positron emission tomography to diagnose parathyroid adenoma, prostate cancer, and hepatocellular carcinoma by evaluating the choline metabolism. In this study, a radiolabeling method for [18F]fluorocholine was optimized using a…

  14. Journal Article Full text

    Geometrical Optimization of Closed-End Cylindrical Air Filter Using CFD Simulation

    K D Lakshitha Rukshan; Foad Faraji; F A Hamad

    대한환경공학회지, Vol. 46 No. 7 · 2024 · Korean · DOAJ

    This research aims to evaluate the effect of porous filter configuration on flow characteristics within filter using CFD simulation. This simulation model was chosen for comprehensive analysis that considers different variables affecting the filter performances. Dynamics of the flow and pressure…

  15. Journal Article Full text

    Lightweight Design of Link Structures for Amphibious Boat using Topology Optimization Method

    Jae Moon Im; Jong Yeon Kim; Kwang Bok Shin et al.

    한국정밀공학회지, Vol. 35 No. 11 · 2018 · Korean · DOAJ Scopus

    In this paper, the topology optimization method was used to describe the lightweight design of link structures for an amphibious boat. Topology optimization was used to determine the optimum density distribution of the structure. The analysis revealed that the link structures for amphibious boat…

  16. Journal Article Full text

    Optimization Design of Penetrator Geometry Using Artificial Neural Network and Genetic Algorithm

    Kyu-Seok Jung; Sung-Min Cho; Jae-Hyeong Yu et al.

    한국정밀공학회지, Vol. 37 No. 6 · 2020 · Korean · DOAJ Scopus

    When the penetrator collides with the target, the penetrator has different penetrating characteristics and residual velocity after penetration, according to the geometry of the penetrator. In this study, we optimized the geometry of the penetrator using the artificial neural network and the genetic…

  17. Journal Article Full text

    Lightweight Design of a Vacuum Gripper for Inspection Equipment Using Topology Optimization

    Euddeum Cha; Tae-Young Kim; Taeho Ha et al.

    한국정밀공학회지, Vol. 38 No. 9 · 2021 · Korean · DOAJ Scopus

    …which previously encompassed assembling eleven components. Topology optimization was used to reduce part weight while maintaining structural rigidity and safety, and two optimization models were designed: two-piece and one-piece models. Based on these optimized geometries, the internal vacuum paths…