Biblio Discovery — Demo Discovery Service

15 hasil untuk "Uwe Scheithauer"

Menampilkan 1–15 · 0,34 detik · RSS

  1. Artikel Jurnal Teks lengkap

    CerAMfacturing of Aluminum Nitride with High Thermal Conductivity via Lithography-Based Ceramic Vat Photopolymerization (CerAM VPP)

    Eric Schwarzer-Fischer; Uwe Scheithauer; Alexander Michaelis

    Ceramics, Vol. 6 No. 1 · 2023 · Inggris · DOAJ Scopus

    Aluminum nitride (AlN) is an excellent material for heat sinks and is used, for example, in high-performance electronics, high-power LEDs and photovoltaics. In order to meet the constantly increasing demands on substrate materials and heat sinks resulting from the permanent increase in power…

  2. Artikel Jurnal

    Effect of infill strategy on the flexural strength of 3Y-TZP bars fabricated by thermoplastic 3D printing (T3DP)

    Ipeknaz Özden; Uwe Scheithauer; Aljaž Iveković dkk.

    Open Ceramics, Vol. 14 · 2023 · Inggris · DOAJ Scopus

    Thermoplastic 3D printing (T3DP) is a ceramic additive-manufacturing (AM) process that uses a thermoplastic feedstock. During T3DP, parts are manufactured by rapid deposition of micron-sized droplets, which fuse and solidify to form lines that fuse further to form layers. This building logic allows…

  3. Artikel Jurnal Teks lengkap

    Influence of Various Binder Jet Printers on the Additive Manufacturing of Hardmetals

    Christian Berger; Johannes Pötschke; Uwe Scheithauer dkk.

    Crystals, Vol. 14 No. 11 · 2024 · Inggris · DOAJ Scopus

    Binder Jetting (BJT), a powder-based additive manufacturing technology, has been shown to be a fast and reproducible green shaping process for many different metals. Due to its high productivity and versatility in material processing, BJT is gaining increasing importance in the manufacturing…

  4. Artikel Jurnal Teks lengkap

    Correlation of Different Cemented Carbide Starting Powders with the Resulting Properties of Components Manufactured via Binder Jetting

    Christian Berger; Johannes Pötschke; Uwe Scheithauer dkk.

    Metals, Vol. 13 No. 11 · 2023 · Inggris · DOAJ Scopus

    For several years, researchers have been exploring the use of the binder jetting powder-based additive manufacturing process to produce WC-Co hardmetals. Compared to other additive manufacturing processes, binder jetting has the potential for high-volume production. However, due to the powder-based…

  5. Artikel Jurnal

    A novel test specimen for strength testing of ceramics for additive manufacturing

    Maximilian Staudacher; Tanja Lube; Jürgen Glettler dkk.

    Open Ceramics, Vol. 15 · 2023 · Inggris · DOAJ Scopus

    This paper introduces a new method for strength testing of additively manufactured ceramics, which was designed to take the characteristics of the manufacturing process into account. It was developed for time- and material efficient specimen fabrication and its design allows adjustment so that…

  6. Artikel Jurnal

    Laser Speckle Photometry investigation of the thermal conductivity of 3D printed ceramic green bodies using Multi Material Jetting

    David Dang; Steven Weingarten; Fernando Frost dkk.

    Open Ceramics, Vol. 8 · 2021 · Inggris · DOAJ Scopus

    Additive Manufacturing (AM) of high-performance materials is becoming more and more established in the market. Especially the field of technical ceramics shows an increasing need for monitoring the manufacturing process in order to identify defects that can be introduced into the component at an…

  7. Artikel Jurnal Teks lengkap

    Reducing the Distortion in Particle Filled Material Extrusion (MEX)-Based Additive Manufacturing (AM) by Means of Modifying the Printing Strategy

    Johannes Abel; Siddharth Tiwari; Milán Kardos dkk.

    Ceramics, Vol. 5 No. 4 · 2022 · Inggris · DOAJ Scopus

    This study addresses a ubiquitous challenge in powder metallurgy: sintering distortion. Sintering distortion can have various causes. On one hand, external factors such as friction with the sintering support during sintering or temperature gradients in the furnace, and, on the other hand, internal…

  8. Artikel Jurnal

    Strength testing of additive manufactured ceramics – A round robin using the CharAM-methodology

    Maximilian Staudacher; Uwe Scheithauer; Maria Reichel dkk.

    Open Ceramics, Vol. 17 · 2024 · Inggris · DOAJ Scopus

    A total of 48 CharAM-specimens were manufactured by four partners in three specimen configurations. Thermal post-processing and testing was conducted at a single partner to minimize other processing variation. The geometry and strength of more than 2000 cantilevers (48 cantilevers per…

  9. Artikel Jurnal

    Potential and challenges for Powder Bed Fusion – Laser Beam (PBF-LB) in industrial ceramic additive manufacturing

    Christian Berger; Gabriela Schimo-Aichhorn; Stefan Gronau dkk.

    Open Ceramics, Vol. 18 · 2024 · Inggris · DOAJ Scopus

    In recent years, ceramic 3D printing has proven its potential for increasing the cost and time efficiency of ceramic manufacturing, especially for customizable products, small series production and for (multi-material) parts with complex design. This work gives an overview of the methods for…

  10. Artikel Jurnal

    Exploring circularity in ceramic 3D printing: Possibilities and implementation

    Matilde Aronne; Eric Schwarzer-Fischer; Valentina Bertana dkk.

    Open Ceramics, Vol. 25 · 2026 · Inggris · DOAJ Scopus

    Nowadays, concepts such as recycling, reusing, and sustainability are gaining ground in a wide range of fields and sectors, including manufacturing. This paradigm shift from “produce-dispose” to “produce-reuse” is pushing manufacturers and producers to move from a linear economy to a circular one…

  11. Artikel Jurnal Teks lengkap

    Potentials of Numerical Methods for Increasing the Productivity of Additive Manufacturing Processes

    Uwe Scheithauer; Tetyana Romanova; Oleksandr Pankratov dkk.

    Ceramics, Vol. 6 No. 1 · 2023 · Inggris · DOAJ Scopus

    Thanks to the layer-by-layer creation of components, additive manufacturing (AM) processes enable the flexible production of components with highly complex geometries, that were previously not realizable or only with very great effort. While AM technologies are very widespread in the research…

  12. Artikel Jurnal

    Assessment of the as-sintered surfaces of ceramic components additively manufactured by vat Photopolymerization (CerAMVPP)

    Nadine Lorenz; Uwe Scheithauer; Eric Schwarzer-Fischer dkk.

    Open Ceramics, Vol. 20 · 2024 · Inggris · DOAJ Scopus

    The aim of this work was to gain an initial impression of the surface quality that can be achieved with additively manufactured ceramic components. For this purpose, an assessment body was generated, which has partially double-curved surfaces that can be scanned using a confocal microscope. After…

  13. Artikel Jurnal Teks lengkap

    Process Data-Based Knowledge Discovery in Additive Manufacturing of Ceramic Materials by Multi-Material Jetting (CerAM MMJ)

    Valentin Lang; Steven Weingarten; Hajo Wiemer dkk.

    Journal of Manufacturing and Materials Processing, Vol. 4 No. 3 · 2020 · Inggris · DOAJ Scopus

    Multi-material jetting (CerAM MMJ, previously T3DP) enables the additive manufacturing of ceramics, metals, glass and hardmetals, demonstrating comparatively high solid contents of the processed materials. The material is applied drop by drop onto a substrate. The droplets can be adapted to the…

  14. Artikel Jurnal

    Recyclability of ceramic powder in CerAM vat photopolymerization

    Matilde Aronne; Eric Schwarzer-Fischer; Alberto Ballesio dkk.

    Open Ceramics, Vol. 25 · 2026 · Inggris · DOAJ Scopus

    The sustainability of the manufacturing industry is becoming an increasingly hot topic, particularly the reintroduction of waste into the production chain. The use of AM of ceramics can reduce waste and enable complex, lightweight designs, however, practical routes to circularity remain…

  15. Artikel Jurnal

    Ceramic additive manufacturing and microstructural analysis of tricalcium phosphate implants using X-ray microcomputed tomography

    Sascha Senck; Jonathan Glinz; Sarah Heupl dkk.

    Open Ceramics, Vol. 19 · 2024 · Inggris · DOAJ Scopus

    Additive manufacturing (AM) of ceramic bone implants from tricalcium phosphate (TCP) offers several benefits for bone regeneration and defect treatment. TCP scaffolds, e.g. featuring lattice or gyroid geometries, can effectively induce bone ingrowth and integration, showing a high potential in the…