150 hasil
Menampilkan 1–20 · 0,30 detik · RSS
نشریه مهندسی دریا
ISSN 1735-7608 · Iranian Association of Naval Architecture and Marine Engineering · 150 artikel di indeks
-
Artikel Jurnal
Application of active nonlinear energy sink to reduce the oscillations of flow exposed circular cylinder
In this paper, passive and active vortex-induced vibration control of a circular cylinder that oscillates freely in longitudinal and transverse directions is investigated by utilization of nonlinear energy sink. The nonlinear energy sink is composed of a mass, a damping and a nonlinear spring that…
-
Artikel Jurnal
Comparison of Dynamic Response of Chinese Lantern and Lazy S Riser Configurations Used in CALM Oil Terminal
The risers are one of the most important components of the CALM oil terminal during the unloading/loading operations of tankers, which are used in two common configurations, including Chinese Lantern and Lazy S. It is common to not consider the interaction between these riser configurations and the…
-
Artikel Jurnal
An obstacle avoidance algorithm for an autonomous underwater vehicle based on fuzzy-virtual potential function and forward looking sonar
Obstacles avoidance problem plays a key role in the performance of the Autonomous Underwater Vehicles (AUVs). Obstacle detection is the first step in the process of crossing an obstacle. Sonar is the most used obstacles detection equipment in aquatic environments. In this research work, a forward…
-
Artikel Jurnal
Lagrangian Modeling of Regular Wave Effect on Sea Pipeline on Permeable Sea Bed
Using offshore pipelines is the most common way to transport oil and gas extracted from oil and gas fields. Since the pipelines are usually located on porous seabed, current pattern around them is complicated. In this study, based on the weakly compressible smoothed particles hydrodynamic method…
-
Artikel Jurnal
Increasing heat transfer rate in heat exchanger of underwater vehicle motor by increasing fluid flow turbulence
Due to limited space and energy, increasing the performance of the underwater marine vehicle motor is one of the most important parameters in the design process. Increasing the performance of the underwater marine vehicle motor is directly related to increasing the efficiency of its cooling heat…
-
Artikel Jurnal
Experimental Analysis of slam-induced pressure on the bow-segment of surface ship
Today, determination of slam-induced pressure is one of the interested issue of the researchers. Water entry of bow section of a ship is experimentally examined, in order to investigation of slamming pressure. This experimental study is distinguished because of the effect of longitudinal curvature…
-
Artikel Jurnal
Investigating the geometry and control surface of AUV robots on hydrodynamics performance
Underwater equipment is a set of marine equipment used for purposes such as exploration, drilling, submarine cabling, maintenance and repair of offshore structures, and military applications. In this research, we try to provide a suitable background for the conceptual design of AUV robots by…
-
Artikel Jurnal
Investigation of the loss of sound signals in the presence of Eddy in a hypothetical area
Marine phenomena that disturb the stratification cause oscillations in the acoustic signals. Among them, Eddies can be effective factors in mixing the ocean and create significant disturbances in the sound field. In this paper, the different parameters of Eddy and the effects of Eddy on sound…
-
Artikel Jurnal
Investigation of the Effect of water level on deep seawater intakes
Feedwater supply for coastal desalination plants, powerplants and other coastal industries using marine intakes has become a common approach during last years. Besides providing water with high quality, intake design should be economically and environmentally acceptable too. The intakes are…
-
Artikel Jurnal
Investigation of the Bulbous Bow Effect on the Resistance of a Container Ship by CFD Method
In commercial ships, wave making resistance is a part of total resistance which to reduce it, a bulbous bow is added to the ship bow. To investigate the effect of bulbous bow on total resistance, a container ship model is simulated with and without the bulbous bow at three Froude Numbers: 0.22…
-
Artikel Jurnal
Estimation of Flushing Time in Semi-Enclosed Water Bodies through a Lumped and Distributed aspects (Case Study: Chabahar Bay)
One of the most important parameters to design any eco-friendly coastal development project at semi-enclosed water bodies like Chabahar bay is the estimation of flushing time. In this paper, Chabahar baychr('39')s flushing as a sensitive water body is investigated considering either a lumped or…
-
Artikel Jurnal
Investigation of Dilution, Frequency, and Intensity of Turbulent Flow in Submerged Disposal of Brine
In recent decades, brine discharge into the water bodies and desalination plants have increased dramatically all over the world. In this research, behavior of turbulent flow in submerged disposal of saline wastewater produced by coastal desalination with a nozzle oriented upwards at 45o to the…
-
Artikel Jurnal
Noise Calculation of Non-cavitating Marine Propellers by Solving FW-H Acoustic Equations
The noise emitted by ships is one of the most important noises in ocean and the propeller noise is one of the major components of the ship noise. Measuring the propeller noise in laboratory despite the high accuracy and good reliability, costs a lot, has some complexities and is very time…
-
Artikel Jurnal
Experimental Study of Tensile Strength in Composite Floats Structure Repaired with Multi-Layer Patches
Repair of cracked composite structural components and plates according to repair standards is increased year on year. Patched repair reduces the stress field near the crack by bridging the stresses between the cracked plate and the composite patch, leads to retardation or complete stoppage of the…
-
Artikel Jurnal
Numerical study of Iran-Bushehr Container Ship motions and added resistance in regular head waves using STAR-CCM+
Nowadays, the optimal use of energy, speed increase, fuel consumption reduction and environmental pollution prevention are essential in the ship design and manufacturing discussion. So it is critical to be able to estimate ship's response to waves, since the resulting added resistance and…
-
Artikel Jurnal
A Field Study of Breaking Zone Width, Breaker Height, and Number of Breakings in the East Coast of Noor
Proper recognition of the coastal area helps to make better use of this area. Due to high risk conditions and wide variations in the coastal area, studies of this area usually cost a lot. In this research, the relationships among the breaking wave height, the width of the breaking zone, and number…
-
Artikel Jurnal
Numerical Investigation of Lift Force Increase in a Hovercraft by Changing the Geometrical Parameters of Flow Transfer Part and Air Channel
Hovercraft is a modern air-cushion vehicle (ACV) that has the ability to move on a variety of surfaces, such as water and land. The distinguishing feature of the hovercraft and other vessels is that the hovercrafts are deployed on a layer of air and then propelled, which is a major factor in the…
-
Artikel Jurnal
Proposed a New Hybrid LOF-ANN Method to Extreme Wave Height Prediction based on Meteorological Data
Extreme wave height prediction is very challenging due to its very high non-stationarity and non-linearity nature. The main aim of the present study is to propose a new hybrid method based on Local Outlier Factor and Artificial Neural Networks classifier, called LOF-ANN, to accurate prediction of…
-
Artikel Jurnal
Feasibility and Experimental Analysis of SPM Translational Motion under the Effect of Regular Wave Using the 3D Image Processing System
Single point mooring terminals are, as the name implies, facilities of small horizontal dimensions, to which large vessels are moored by means of a bow hawser or by any other means which allows the vessel to rotate 360 around the mooring point. Generally, the single point mooring terminal can have…
-
Artikel Jurnal
Presentation of New Design of Perforated Half-Depth Wall Breakwater
The present study aims to introduce a new lattice wall breaker. The wall of this breaker is made up of small PVC cubic elements (PVC). Each of these cuboid shapes (blocks) has two holes, which, when placed on each other and through the metal cable through them, blocks are woven together. In the…