451 results
Showing 1–20 · 0.30 seconds · RSS
Journal of Sensors and Sensor Systems
Scopus
ISSN 2194-8771 · Copernicus Publications · 451 articles in the index
-
Journal Article Full text
Towards exclusive use of SI units in sensor systems
In times of digital transformation, machines are expected to operate exclusively using the International System of Units (SI), something that humans have not yet fully achieved. The same should include sensor systems feeding data to those machines. This requires an internationally authoritative…
-
Journal Article Full text
Inline gas-phase sampling methods for contaminant monitoring in polyolefin recycling
This article investigates methods for sampling volatiles on a compounding extruder to enable the development of a quasi-continuous automated sampling and measurement system for odorous contaminants. A first prototype of a bespoke extraction system was presented in earlier work, comprising four…
-
Journal Article Full text
Recognising wild animals on roads: multisensor systems for accident avoidance
Wildlife-related traffic accidents represent a persistent hazard on rural roads in Germany and beyond. Current electronic wildlife warning systems typically monitor only very short distances and therefore cannot provide large-area coverage. This paper presents a novel multisensor approach that…
-
Journal Article Full text
Towards high-frame-rate data acquisition for ultrasound and photoacoustic imaging with high signal-to-noise ratio
We present an eight-channel evaluation board that enables fast data acquisition for ultrasound sonography (USG) and photoacoustic imaging (PAI). High frame rates enable averaging, resulting in an improved signal-to-noise ratio (SNR). A high SNR is becoming increasingly important in photoacoustic…
-
Journal Article Full text
Modeling and extraction of residual stresses in some MEMS multilayer systems
The intrinsic stresses introduced during the MEMS multilayer deposition process and the thermal stresses introduced during operation can significantly impact the performance, reliability, and lifetime of the product. The mechanical properties of the MEMS multilayer system are analyzed. An accurate…
-
Journal Article Full text
Three-dimensional density field reconstruction of vehicle exhaust plumes using 3D gas schlieren imaging sensor system for remote emission sensing applications
Emission measurement of on-road vehicles in traffic is an important step for air pollution control and, thus, the reduction of negative effects on public health. Remote emission sensing (RES) is a state-of-the-art technology to detect high emitters by monitoring thousands of vehicles in traffic…
-
Journal Article Full text
Development and optimization of an OF-CEAS system for stable isotopic ratio analysis of methane (δ13C-CH4) in the mid-infrared
High-precision analysis of the stable isotopic composition of atmospheric methane (CH4) is essential for attributing its sources and sinks and for a more precise understanding of the global methane cycle. Although conventional isotope ratio mass spectrometry (IRMS) provides high accuracy, it lacks…
-
Journal Article Full text
High-resolution characterization of the size-of-source effect via a continuously variable aperture
The size-of-source effect (SSE) is a major source of uncertainty in radiation thermometers and thermal imaging cameras. This effect is considered a systematic error and is typically evaluated by measuring changes in the detected signal as the size of the radiant source is varied using a set of…
-
Journal Article Full text
Application of artificial intelligence to determine the phase fraction of welded duplex steels using neural networks with partial use of augmented data
This paper addresses the application of artificial intelligence in metallography. The aim is to determine the phase fractions of ferrite and austenite in the weld zone of duplex stainless steel based on the evaluation of metallographic microscopic micrographs. The idea arose from the motivation to…
-
Journal Article Full text
Adaptive accuracy enhancement for a simultaneously firing optical position sensor
An algorithm for adaptive accuracy enhancement of lateral position sensing based on quadrature spatio-temporal modulation is presented, and its application in a prototype micropower optical position sensor with simultaneously firing infrared emitters is reported. Substantial (4×) improvement in…
-
Journal Article Full text
Active Q factor control of MEMS cantilevers by integrated piezoelectric transducers for high-speed AFM applications under vacuum
The first choice in science and industry to image surfaces down to the sub-nm range are scanning electron microscopy (SEM) and atomic force microscopy (AFM). Both techniques have specific disadvantages which can be compensated by the other method. Therefore, the implementation of AFM inside an SEM…
-
Journal Article Full text
In situ casting of polyvinyl chloride membranes in agar-bridged extended-gate field effect transistor sensors
The recent bridged EGFET (extended-gate field effect transistor) sensor design is the most user-friendly potentiometric transducer concept to date. Manufacturing of the sensor, the introduction of a sensitised phase transfer membrane by in situ casting, and transduction of the electric potential…
-
Journal Article Full text
Automated contactless characterization of local thin film thickness and film stress with standard MEMS structures at wafer level
The fabrication of microelectromechanical systems (MEMS) devices comprises many steps, each of which adds to the tolerance, resulting in device performances that may fall outside the defined limits in the design process. Hence, it is important to know local thin film properties most accurately…
-
Journal Article Full text
Detection of geomagnetically induced currents on single phases in power grids using a fiber optic current sensor system
Power transformers are an integral part of our electric power system. Parasitic direct currents in the alternating-current grid cause inefficient transformer operation and demand mitigation measures to protect the grid’s constituents. In particular, geomagnetically induced currents (GICs) arising…
-
Journal Article Full text
Non-contacting determination of the piezoelectric coefficient d33 of lithium tantalate from room temperature up to 400 °C
In this study, a non-contact, optical methodology based on laser-Doppler vibrometry (LDV) is presented to directly determine the piezoelectric constant d33 of LiTaO3 in a temperature range from room temperature to 400 °C as a proof of concept for high-temperature piezoelectric characterization…
-
Journal Article Full text
Towards fully automated metrological traceability in process monitoring: a demonstrator approach highlighting the benefits of Digital Calibration Certificates (DCCs)
The implementation of automation in the metrological traceability of measurements has been demonstrated to possess considerable potential for enhancing the effectiveness of quality management. This enhancement is achieved by decreasing the necessity for human interaction and reducing the risks…
-
Journal Article Full text
EyeOnWater Raspberry Pi: a do-it-yourself maker sensor system project to measure and classify natural water colour based on the Forel–Ule scale
The EyeOnWater Raspberry Pi (EOW–RPI) is a do-it-yourself maker project for citizen science to measure and classify the natural colour of water. It describes the systematic development (from concept to the prototype and application) and evaluation of a replicable optical sensor system that enables…
-
Journal Article Full text
Reverse electrowetting-on-dielectric (REWOD) human energy harvester towards hybridisation with piezoelectricity for self-powered wearable biosensors
Wearable biosensors play a crucial role in modern healthcare, providing continuous monitoring of various physiological parameters. However, the reliance on batteries that require replacement introduces interruptions in the data acquisition process and patient discomfort, and for this reason, energy…
-
Journal Article Full text
Development and analysis of microbridge resonators for reduced pull-in voltage and preserved resonant frequency
This study presents a novel design methodology for microbridge resonators aimed at reducing pull-in voltage while maintaining resonant frequency. Previous studies have primarily focused on adjusting resonator plate geometry, modifying anchor conditions, or altering material properties to control…
-
Journal Article Full text
Local pressure field distribution of bistable PMUTs for distance sensing
This work presents both the directivity pattern and distance dependence of the pressure field of a piezoelectric micromachined ultrasonic transducer (PMUT). The PMUT comprises a silicon membrane and an integrated piezoelectric transducer based on aluminum nitride (AlN) and exploits bistability to…