581 hasil
Menampilkan 1–20 · 0,20 detik · RSS
Приборы и методы измерений
ISSN 2220-9506 · Belarusian National Technical University · 581 artikel di indeks
-
Artikel Jurnal
UIM-1 Measuring Complex for Comprehensive Evaluation of Mechanical Properties of Materials by Instrumented Indentation
Traditional destructive methods for evaluating the mechanical properties of materials require the preparation of test specimens, which precludes their application for assessing finished products. Thus, the development of non-destructive testing that provide reliable evaluation of a wide range of…
-
Artikel Jurnal
Development of Picosatellites’ Experimental Models and a Multi-Device Deployment System for Group Flight Testing in Atmospheric Conditions
Multi-satellite orbital constellations enable transition from single, expensive spacecraft to unified platforms whose aggregate characteristics: global coverage, high reliability and resolution, ability to execute targeted tasks in parallel, flexibility, and scalability – significantly exceed…
-
Artikel Jurnal
Experimental Setup for Detecting Fluorescence Signals of Samples in Microfluidic Devices Reactors
Genetic analysis in microfluidic devices commonly relies on detection of fluorescence intensity from dyes bound to DNA fragments. Aim of this work was to develop an experimental setup and a method for obtaining fluorescence intensity of liquids placed in microfluidic chips by analyzing digital…
-
Artikel Jurnal
Complex Influence of Probe–Sample System Parameters on the Probe Oscillation Mode and Formation of Bistability in Tapping Atomic Force Microscopy
Engaging the tapping mode in atomic force microscopy does not guarantee intermittent-contact interaction; depending on the parameters combination, the probe–sample system may instead exhibit non-contact (attractive) or mixed behavior. The mixed mode is undesirable due to scanning instability, known…
-
Artikel Jurnal
Experimental Evaluation of Damping Suspension Performance for Unmanned Aerial Vehicle Camera Equipment Using Combined Optical Flow and Inertial Sensor Analysis
Ensuring stabilization of imaging equipment onboard unmanned aerial vehicles is a critical factor for the quality of aerial photography and spectrometric measurements, while objective comparative assessment of the effectiveness of various damping suspensions under real flight conditions remains a…
-
Artikel Jurnal
Acoustic Investigation of Elastic Properties of Closed-Cell Polyolefin Foam Sheets under Static Tension
Polyolefins are widespreadly used in strategically important industries due to their high thermal, sound and vibration insulation properties. During the process of application these materials are subjected to various mechanical influences leading to their deformation and changes in properties. Aim…
-
Artikel Jurnal
Polygraphic Cell for Tissue Breathing Research
Tissue respiration is a multistage biochemical process during which cells obtain energy through the oxidation of organic substances. Studying this process is essential for understanding pathogenesis of many diseases. Aim of this study was to improve the method for studying tissue respiration of…
-
Artikel Jurnal
Measurement and Computational Approach for Evaluating the Effect of Physical Heterogeneity at the Bolus-Phantom Interface on Photon Beam Dosimetric Parameters
Modern radiation therapy requires reproducible dose delivery to superficial and near surface structures. An important source of uncertainty is the loss of contact between the bolus and the patient’s skin, leading to air gaps at the bolus–skin interface. The aim of this study was to assess the…
-
Artikel Jurnal
Electronic Shooting Simulator Family "STrIzh": Development of Mock-Ups and Investigation of the Initial Level Simulator Error
Development of rifle electronic simulators (i.e. for hand weapons and not using ammunition) is an important task, since the production of any type of small arms, according to regulatory documents, also requires the production of a simulator to instill aiming and firing skills. The developing family…
-
Artikel Jurnal
Measurement of Intermode Dispersion in Short Sections of Multimode Optical Fiber Guides
Measuring the intermode dispersion in short sections (from units to tens meters in length) of multimode optical fibers is often an actual task. Мethods used based on Mach–Zehnder interferometers have typical disadvantages inherent for interferometric measurement methods. Рurpose of the paper was to…
-
Artikel Jurnal
Bandwidth-Enhanced Pentagon-Shaped Microstrip-Based Planar Monopole Antenna with Harmonic Rejection
Microstrip patch antennas' two primary limitations are narrow bandwidth and harmonic interference, restricting their application for 2.4 GHz systems. Standard microstrip patch antennas typically only provide a fractional bandwidth between 2 % and 5 %. Because of the higher-order harmonic emissions…
-
Artikel Jurnal
Machine Learning in Understanding the Initial Interaction of the Atomic Force Microscope Probe with the Surface
Reliable determination of the tip-surface contact in atomic force microscopy measurements is necessary for structural and physico-mechanical analysis of the surface properties. Transition from non-contact interaction to contact one during experiments in air environment is accompanied by a rapid…
-
Artikel Jurnal
Optimization of the Optical Measuring Converter’s Geometric Properties for the Microelectromechanical Pressure Sensor
Nowadays development and production of microelectromechanical systems is one of the most promising directions in the world's economy. One of the innovative fields in the development of microsystems is integration of optical devices as measuring transducers. Goal of the paper is optimization of the…
-
Artikel Jurnal
Scanning Ion-Conductance Microscopy: Operating Principles and Advantages for Medical and Biological Practices
Study of medical and biological objects poses fundamentally new challenges for scanning probe microscopy methods, as the assessment of living systems requires a method to be not only high-resolution but also high-speed, enabling long-term dynamic observations in the most physiologically relevant…
-
Artikel Jurnal
Prospects for using Chromel-Alumel Thermocouples TChA (Type K) with Normalizing Converters Based on Neural Network Methods of Linearization and Compensation of ThermoEMF Instabilities. Short Review
The object of study is implementation of normalizing converters based on neural network methods to increase the accuracy of temperature measurements with Chromel-Alumel thermocouples (Type K). Detailed analysis of physical and technical limitations of Type K thermocouples is conducted including…
-
Artikel Jurnal
Algorithm for Measuring the Geometric Parameters of Optical Freeform Surfaces Using a Coordinate Measuring Machine
Nowadays use of freeform surfaces in optical systems for various purposes – from mobile displays to space optics – becomes increasingly popular. This design solution makes it possible to create a system with a minimum number of components, low weight, and high image quality. However, as the…
-
Artikel Jurnal
Prototype of High-Precision AC Voltage Measuring Converter
Evaluation of electrical signals’ level with various shapes, such as sinusoidal or rectangular, pulse trains, random, etc., is most often carried out based on the root-mean-square value of voltage and the peak factor. Analysis performed showed absence of mass-produced domestic high-precision…
-
Artikel Jurnal
Laboratory Simulator of Airborne Video‑Spectral Experiments for Calibration of Earth Remote‑Sensing Instruments
Airborne and spaceborne video-spectral imaging is a key tool for remote sensing of the Earth's surface and atmosphere; however, its accuracy critically depends on rigorous pre-flight calibration and verification of the instrumentation. The aim of this work is to develop and demonstrate a laboratory…
-
Artikel Jurnal
Statistical Detection and Removal of Noise Outliers in Visualized Probe Electrometry Data
The increasing volume of measurement information makes manual processing impractical, while existing algorithms demonstrate limited effectiveness (up to 93 %). The aim of this work was to develop a combined algorithm based on a synthesis of existing methods to improve the accuracy and reliability…