614 hasil
Menampilkan 1–20 · 0,51 detik · RSS
Вестник Самарского университета: Аэрокосмическая техника, технологии и машиностроение
ISSN 2542-0453 · Samara National Research University · 614 artikel di indeks
-
Artikel Jurnal
Induced interference model analysis in airborne electromagnetics
This article analyzes existing induced interference models and their modifications to select the best ones for subsequent compensation of its influence on measurement results. Possible options for improving quality of compensation are considered. For this purpose, comparative analysis of several…
-
Artikel Jurnal
Optimization of the combined launch profile for placing spacecraft into low-inclination orbits
The paper discusses the problem of optimizing an interorbital transfer of a spacecraft to a near-circular low-inclination orbit using a combined launch profile. In this scenario, the launch vehicle places the upper stage and the spacecraft into a reference low Earth circular orbit. The upper stage…
-
Artikel Jurnal
Methodology for the design assessment of reliability of spacecraft windows using logical-and-probabilistic methods
It is shown that the method of reliability block diagrams is not always applicable for spacecraft window elements complex in terms of structural composition and interdependencies in failures. A methodology is proposed for assessing the probability of failure-free operation of spacecraft windows…
-
Artikel Jurnal
Numerical study of acoustic characteristics of sound-absorbing structures of various configurations
The acoustic characteristics of Helmholtz resonators with various configurations in the frequency range of 500…3000 Hz were simulated. The influence of the resonator shape, perforation diameter, volume and position of the resonator neck on the natural frequency and sound absorption coefficient…
-
Artikel Jurnal
Study of the effect of homogenization and hot rolling practices on properties formation in high-magnesium alloys with Sc, Hf, Er, Zr additions
The influence of chemical composition and thermomechanical processing conditions on the mechanical properties of aluminum alloys of the Al-Mg system was studied. The influence of the main alloying element (Mg) and microalloying additives (Sc, Zr, Er, Hf), as well as hot rolling temperature, on the…
-
Artikel Jurnal
Identification of disturbances and parameters of optical flow in vision systems
A new approach to identifying the parameters of optical flow (optical velocity fields) is proposed with simultaneous estimation of the methodological error arising from the assumption that each pixel in a scene maintains its intensity between the current and subsequent frames. The proposed approach…
-
Artikel Jurnal
Structural and parametric synthesis of hydromechanical regulators of the aircraft emergency system with a power transmission unit
The emergency subsystem of a passenger aircraft containing a power transmission unit as an object of regulation is considered. For the structural synthesis of new types of automatic control systems for the emergency system of an aircraft, the hydromechanical regulators of hydraulic machines…
-
Artikel Jurnal
Engine fan case dynamic deformation and failure criteria in blade-out modelling
The article describes the results of numerical and experimental study of dynamic deformation and rupture of aluminum plates (imitators of the engine case) hit by titanium plates (blade imitators). The impingement speed of the plates is in the range of 160…239m/s. The numerical solution of the…
-
Artikel Jurnal
Algorithm for collaborative robot motion planning with collision resolution based on RL agent
One of the main requirements for modern collaborative robotic processes is the efficiency of management in resolving collisions with objects in the work area and ensuring a given level of safety during the movement of the robot. Modern universal collision resolution algorithms do not always form a…
-
Artikel Jurnal
Procedures for design and structural-parametric synthesis of tribotronic rotor supports
Based on the analysis of the features of tribotronic systems functioning, approaches to the integrated implementation of interrelated procedures for designing active rotor supports were developed. A generalized algorithm for the structural-parametric synthesis of tribotronic fluid film bearings…
-
Artikel Jurnal
Influence of the scale factor on the characteristics of turbopumps of ultra-light launch vehicles’ engines
Currently, the use of ultra-light launch vehicles for launching nano- and microsatellites is actively developing in the world, which requires the creation of engines with relatively low thrust. In this paper, based on criterion dependencies, the change in the characteristics of turbopump units of…
-
Artikel Jurnal
Analysis of control programs for the deployment of a space system with an uninsulated conductive tether
Management programs for the deployment of a space tether system along the local vertical in low-Earth orbit are analyzed. The system consists of a small spacecraft, an uninsulated conductive tether and a load (electron emitter). The use of non–insulated conductive tether is one of the ways to…
-
Artikel Jurnal
Determining characteristics of the inlet collector with interceptor for gas turbine engine test rig
To determine the characteristics of an inlet channel with a segmented interceptor used to generate inlet non-uniformity in a gas turbine engine during bench testing, a numerical quasi-steady-state model of non-uniform flow is proposed. Its distinctive feature is that turbulent flow pulsation is…
-
Artikel Jurnal
Adaptive algorithm for engine acoustic diagnostics with limited data
The article discusses modern approaches to the development of intelligent vibration diagnostics systems capable of working with small amounts of data and adapting to changing equipment operating conditions. An algorithm based on machine learning methods is presented, which uses clustering for data…
-
Artikel Jurnal
Modeling and justification of technological parameters in line-based surface plastic deformation of cylindrical parts
This paper presents the results of a numerical simulation of the line surface plastic deformation process for cylindrical parts made of steel 45. The influence of the process parameters, namely the spacing between deformation tracks, the roller feed speed, and the radial interference, on the…
-
Artikel Jurnal
Method for aircraft condition evaluation by a sequence of its images
We propose a method of estimating an aircraft’s angular motion parameters based on a real-time sequence of images recorded by an optical system. This study aims to implement a new approach that enables remote aircraft identification without using sounding signals. The method uses a vector model to…
-
Artikel Jurnal
Health assessment of planetary gearboxes for gas-turbine engines under operating conditions
The study demonstrates that for assessing the condition of aircraft gas-turbine engine gearboxes during on-site operation, the most effective method is analyzing speed signals from standard onboard tachometers on their input and output shafts. The use of these signals, compared to vibration…
-
Artikel Jurnal
Refinement of the internal forces energy for the fuel tank diaphragm
A refined expression for the strain rate intensity is determined for the refined plastic deformation zone of metal eversible diaphragms in fuel tanks. The integral on the right side of the energy principle equation is solved, taking into account the refined intensities. A refined expression for the…
-
Artikel Jurnal
Development of a kinematic scheme for an advanced stretch bending press
The article focuses on the development of a new kinematic scheme for an advanced stretch bending press designed for manufacturing aircraft frame segments. An analysis of existing technologies for frame production was conducted, including milling from plates, isothermal stamping, and stretch…
-
Artikel Jurnal
Optimization of the cooling system of the head part of the combustion chamber of the gas turbine engine
Optimal distribution of cooling air is a pressing issue. This problem must be addressed during combustion chamber design and fine-tuning. Burnout of combustion chamber components often occurs during operation. This requires the implementation of new design solutions for air redistribution to ensure…